Frontline BSF Tech Guide - Revision history

Jared: /* Audio: */

2026-04-27T20:16:19Z

Audio:

← Older revision		Revision as of 20:16, 27 April 2026
Line 9:		Line 9:
	# Select yes to load User scene		# Select yes to load User scene
	# Turn on green “ON” button to the right of the board on the booth wall		# Turn on green “ON” button to the right of the board on the booth wall
	# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the desk behind the stage		# Grab Microphone 3, Lav 1, and Acoustic 1 (Plus Microphone 1 and Microphone 2 if you need the extra HH channel) from the desk behind the stage
	#* Mic 1 needed first meeting of the month for treasurer's report.		#* Mic 1 and/or 2 needed first meeting of the month for treasurer's report and during open share nights.
	# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 2”		# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 2”

Jared: /* Lighting: */

2025-10-20T19:25:38Z

Lighting:

← Older revision		Revision as of 19:25, 20 October 2025
Line 15:		Line 15:
	== Lighting: ==		== Lighting: ==

			# If house lights are off, press the "Preset 1" button on any of the wall-stations near the doors to the worship center.
	# Power the stage lights by pressing the rocking power switch next to the blue lighting console once.		# Power the stage lights by pressing the rocking power switch next to the blue lighting console once.
	# Wake up the lighting computer by moving the mouse.		# Wake up the lighting computer by moving the mouse.
Line 20:		Line 21:
	# On the blue lighting board, hold the shift button and press the “REL” button.		# On the blue lighting board, hold the shift button and press the “REL” button.
	# Pull fader four all the way down, and the push it all the way up.		# Pull fader four all the way down, and the push it all the way up.
	~~# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”~~
	~~# If sections of the house lights above the seat are dark, turn off the switch on “Rack 3” in the back and turn back on.~~

	== Video: ==		== Video: ==

Jared at 19:54, 8 September 2025

2025-09-08T19:54:49Z

Jared: /* Shutdown & Posting to MyBSF */

2025-08-25T20:20:45Z

Shutdown & Posting to MyBSF

Jared: /* Lighting: */

2025-08-25T20:07:53Z

Lighting:

← Older revision		Revision as of 20:07, 25 August 2025
Line 14:		Line 14:
	== Lighting: ==		== Lighting: ==

			# Power the stage lights by pressing the power switch next to the blue lighting console once.
	# Wake up the lighting computer by moving the mouse.		# Wake up the lighting computer by moving the mouse.
	# Log into user “lights” - the password is: Lights		# Log into user “lights” - the password is: Lights
	# On the blue lighting board, hold the shift button and press the “REL” button ~~a few times~~.		# On the blue lighting board, hold the shift button and press the “REL” button.
	# Pull fader four all the way down, and the push it all the way up.		# Pull fader four all the way down, and the push it all the way up.
	# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”		# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”
	# If sections of the house lights above the seat are dark, turn off the switch on “Panel 3” in the back and turn back on.		# If sections of the house lights above the seat are dark, turn off the switch on “Panel 3” in the back and turn back on.

	== Video: ==		== Video: ==
Line 26:		Line 27:
	# Remove lens cap		# Remove lens cap
	# Using the two controls coming from the camera, zoom and focus the camera. (items outlined in red are in focus, That’s what we’re looking for!)		# Using the two controls coming from the camera, zoom and focus the camera. (items outlined in red are in focus, That’s what we’re looking for!)
	# ~~Keep~~ the ~~video director~~ computer ~~turned on and signed into~~ the ~~Frontline Church login. If it's logged out~~, log in using password frontLINE33.		# If the computer next to the video switcher is shut down, log in using the password: frontLINE33.
	# Ensure there is an SD card plugged into the video recorder under the computer. If not, plug one in!		# Ensure there is an SD card plugged into the video recorder under the computer. If not, plug one in!
	# Press the Setup Button on the button ~~pad left of the computer~~.		# On the button pad next to the video switcher, navigate to the BSF window by pressing "menu" then "BSF".
			# Press the Setup Button on the button.
	# Make sure you see the correct camera on the right screen		# Make sure you see the correct camera on the right screen
	# Press FTB on the left video switcher.		# Press "TV UP" on the button pad to raise the teaching TV. (If this doesn't work, the old remote is in the drawer under the desk)
			# Press FTB on the top left of the video switcher.

	== Slides: ==		== Slides: ==

	# ~~Turn on~~ the slides computer		# Restart the slides computer.
	# Log into the BSF user using password “Frontline” - Case sensitive		# Log into the BSF user using password “Frontline” - Case sensitive
	~~# Press the down arrow on the black box on the back of the tech booth to lower rear screen~~
	~~# Using the Black remote with orange tape on it, raise the TV from the stage. Use the Samsung remote to turn on the TV (These remotes are usually on the higher level by the video computer.~~
	# Turn on TV in front of the camera position.		# Turn on TV in front of the camera position.
	# On the slides computer, open Chrome and select user “Admin”		# On the slides computer, open Chrome and select user “Admin”
Line 45:		Line 46:
	# Right click and delete the previous week’s presentations from the left side of Propresenter		# Right click and delete the previous week’s presentations from the left side of Propresenter
	# Select each file and let Powerpoint open on its own and load the presentations into the left bar of ProPresenter.		# Select each file and let Powerpoint open on its own and load the presentations into the left bar of ProPresenter.

	If a slide doesn’t show up correctly, open the PowerPoint file and go to the slide in question. Then go to file and select export, choose jpeg, and single slide. Save it to the downloads folder and drag that slide into the presentation to replace the incorrect one.

	= During the lecture =		= During the lecture =
Line 54:		Line 53:
	# The right most fader will be your overall volume. To the left of that are all of your individual channels.		# The right most fader will be your overall volume. To the left of that are all of your individual channels.
	# Regulate the volume of items to make sure they are heard clearly. When a channel is not in use, press the mute button above the fader until it is illuminated red.		# Regulate the volume of items to make sure they are heard clearly. When a channel is not in use, press the mute button above the fader until it is illuminated red.
	# If there is not sound online. Press the button on the right labeled Stream. Then, ensure the main fader is up to -10.		# If there is not sound online:
	# Ensure the channel you are not hearing is also up.		## Press the button on the right labeled Stream.
	# Press the “LR” button above the main fader to go back to mixing the sound in the room.		## Then, ensure the main fader is up to -10.
			## Ensure the channel you are not hearing is also up.
			## Press the “LR” button above the main fader to go back to mixing the sound in the room.

	== Video: ==		== Video: ==

	# Before the music starts, make sure the “FTB” button on the ~~small~~ video switcher is flashing red.		# Before the music starts, make sure the “FTB” button on the video switcher is flashing red.
	# Press the green start button on the button pad		# Press the green start button on the button pad to start the recording
	# As the music starts, press ~~the green start button to the left of the computer and~~ “FTB” button.		# As the music starts, press “FTB” button.
	# You should now see the image on the screen		# You should now see the image on the screen
	# Open the facebook page and youtube channel to ensure the stream is working		# Open the facebook page and youtube channel to ensure the stream is working
	# If you need to show a video from the screen online, press the ~~“play video”~~ button.		# If you need to show a video or image from the screen online, press the “slide” button.
	# At the end of the lecture, press the red stop button on the button pad, and press the “FTB” button so that it is flashing red.		# At the end of the lecture, press the red stop button on the button pad, and press the “FTB” button so that it is flashing red.

Line 93:		Line 94:
	# Click download, under the three dots next to the video title. Choose the cues you set as the start and end points		# Click download, under the three dots next to the video title. Choose the cues you set as the start and end points
	# Once the file downloads, upload it to myBSF from the downloads folder.		# Once the file downloads, upload it to myBSF from the downloads folder.
			# * If the livestream video is unavailable or unusable *
			## Remove the SD card from one of the video recorders next to the video switcher.
			## Plug it into the back of the lighting computer.
			## Open Finder and find the SD Card under locations.
			## Move the relevant file to the downloads folder and upload to myBSF as usual.
	# Press the red “OFF” button on the wall to the right of the sound board.		# Press the red “OFF” button on the wall to the right of the sound board.
	# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.		# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.
	# Everything should be shut off now except the computer =)		# Everything should be shut off now except the computer =)
	# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.		# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.
	# ~~Use~~ the ~~Orange taped remote~~ to ~~retract~~ the TV ~~within the stage~~.		# Press the "TV Down" button to lower the teaching TV.
	# Replace the lens cap on the camera ~~(It should already be powered off)~~		# Replace the lens cap on the camera.
	# ~~Turn off~~ the ~~Video and Presentation computers~~		# Restart the slides computer.

Jared: /* Lighting: */

2025-08-25T19:26:06Z

Lighting:

← Older revision		Revision as of 19:26, 25 August 2025
Line 14:		Line 14:
	== Lighting: ==		== Lighting: ==

	# ~~Turn on~~ lighting computer. ~~behind the bottom left corner~~		# Wake up the lighting computer by moving the mouse.
	# Log into user “lights” - the password is: Lights		# Log into user “lights” - the password is: Lights
	# On the blue lighting board, hold the shift button and press the “REL” button a few times.		# On the blue lighting board, hold the shift button and press the “REL” button a few times.

Jared: /* Audio: */

2025-08-25T19:15:40Z

Audio:

← Older revision		Revision as of 19:15, 25 August 2025
Line 10:		Line 10:
	# Turn on green “ON” button to the right of the board on the booth wall		# Turn on green “ON” button to the right of the board on the booth wall
	# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the storage room behind the stage		# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the storage room behind the stage
	# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 3”		# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 2”

	== Lighting: ==		== Lighting: ==

Jared: /* Video: */

2025-04-27T18:11:22Z

Video:

← Older revision		Revision as of 18:11, 27 April 2025
Line 26:		Line 26:
	# Remove lens cap		# Remove lens cap
	# Using the two controls coming from the camera, zoom and focus the camera. (items outlined in red are in focus, That’s what we’re looking for!)		# Using the two controls coming from the camera, zoom and focus the camera. (items outlined in red are in focus, That’s what we’re looking for!)
	# ~~Turn off~~ the video computer ~~if it is not already off. By holding the power button for five seconds.~~		# Keep the video director computer turned on and signed into the Frontline Church login. If it's logged out, log in using password frontLINE33.
	~~# Turn the video computer back~~ on.		# Ensure there is an SD card plugged into the video recorder under the computer. If not, plug one in!
	~~# Log~~ into the ~~BSF user~~, using password ~~“Frontline”~~		# Press the Setup Button on the button pad left of the computer.
	# Ensure there is ~~a thumb drive~~ plugged into the ~~small~~ video ~~switcher on~~ the ~~right~~. If not, plug one in!		# Make sure you see the correct camera on the right screen
	~~# Make sure the Blue circle underneath “STOP” on the Silver HP monitor shows a time greater than 1 hours. If not, plug the drive into a computer and delete any files off it.~~
	# Press the Setup Button on the button pad left of the computer
	# Make sure you see the correct camera ~~and picture in picture~~ on the right screen
	# Press FTB on the left video switcher.		# Press FTB on the left video switcher.

Zero: Added FL BSF Page

2024-07-30T15:58:03Z

Added FL BSF Page

New page

[[File:BSF Logo.png|center|frameless|585x585px]]

= SETUP =

== Audio: ==

# Turn on soundboard (Press the power button on the pad above the soundboard and then press “System On”)
# When asked to login, select BSF, then login, the password is “BSF” - all caps
# Select yes to load User scene
# Turn on green “ON” button to the right of the board on the booth wall
# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the storage room behind the stage
# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 3”

== Lighting: ==

# Turn on lighting computer. behind the bottom left corner
# Log into user “lights” - the password is: Lights
# On the blue lighting board, hold the shift button and press the “REL” button a few times.
# Pull fader four all the way down, and the push it all the way up.
# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”
# If sections of the house lights above the seat are dark, turn off the switch on “Panel 3” in the back and turn back on.

== Video: ==

# (Note, use the camera on the RIGHT)
# Remove lens cap
# Using the two controls coming from the camera, zoom and focus the camera. (items outlined in red are in focus, That’s what we’re looking for!)
# Turn off the video computer if it is not already off. By holding the power button for five seconds.
# Turn the video computer back on.
# Log into the BSF user, using password “Frontline”
# Ensure there is a thumb drive plugged into the small video switcher on the right. If not, plug one in!
# Make sure the Blue circle underneath “STOP” on the Silver HP monitor shows a time greater than 1 hours. If not, plug the drive into a computer and delete any files off it.
# Press the Setup Button on the button pad left of the computer
# Make sure you see the correct camera and picture in picture on the right screen
# Press FTB on the left video switcher.

== Slides: ==

# Turn on the slides computer
# Log into the BSF user using password “Frontline” - Case sensitive
# Press the down arrow on the black box on the back of the tech booth to lower rear screen
# Using the Black remote with orange tape on it, raise the TV from the stage. Use the Samsung remote to turn on the TV (These remotes are usually on the higher level by the video computer.
# Turn on TV in front of the camera position.
# On the slides computer, open Chrome and select user “Admin”
# Go to google drive and download the weekly lecture notes and song lyrics from drive.google.com
# They will be under the Lecture Resources > Class Night Lecture & worship PowerPoints folder, right click to download
# Open ProPresenter and click file > Import > Powerpoint - the files will be in the downloads folder
# Right click and delete the previous week’s presentations from the left side of Propresenter
# Select each file and let Powerpoint open on its own and load the presentations into the left bar of ProPresenter.

If a slide doesn’t show up correctly, open the PowerPoint file and go to the slide in question. Then go to file and select export, choose jpeg, and single slide. Save it to the downloads folder and drag that slide into the presentation to replace the incorrect one.

= During the lecture =

== Audio: ==

# The right most fader will be your overall volume. To the left of that are all of your individual channels.
# Regulate the volume of items to make sure they are heard clearly. When a channel is not in use, press the mute button above the fader until it is illuminated red.
# If there is not sound online. Press the button on the right labeled Stream. Then, ensure the main fader is up to -10.
# Ensure the channel you are not hearing is also up.
# Press the “LR” button above the main fader to go back to mixing the sound in the room.

== Video: ==

# Before the music starts, make sure the “FTB” button on the small video switcher is flashing red.
# Press the green start button on the button pad
# As the music starts, press the green start button to the left of the computer and “FTB” button.
# You should now see the image on the screen
# Open the facebook page and youtube channel to ensure the stream is working
# If you need to show a video from the screen online, press the “play video” button.
# At the end of the lecture, press the red stop button on the button pad, and press the “FTB” button so that it is flashing red.

== Slides: ==

# Click through the slides of the worship songs. Make sure to advance the slide as people are singing the last word of the current slide so they have a chance to read the next line before singing it.
# At the beginning of the teaching, click on the first slide.
# If the teacher is using the clicker, stand by and help as needed. Otherwise, advance the slides for the teacher as they go.

== Sharing Livestream Access: ==

# Navigate to studio.resi.io and click on the dashboard. Click on the dashboard tab, and select the lecture from the live and upcoming box.
# Under the watch tab, click on YouTube, and scroll down.
# Copy the YouTube video link from the box.
# Click on the group bookmark in the bookmark bar.
# Post that link to the BSFGRNEW - Lecture only group.
# Send that same link via gmail.com to EWLansingBSF@gmail.com , giertie@yahoo.com , Nikihaynes22@aol.com , knjroot@yahoo.com , akingsworthy@hotmail.com , Margaret.sharp73@gmail.com

''NOTE: use CMD (next to the space bar) + C or V to copy and paste. =)''

= Shutdown & Posting to MyBSF =

# Once the lecture is done, go to studio.resi.io
# Log in under the user rvanderploeg@frontlinegr.com with password “frontLINE33”
# Under the dashboard tab, click on the lecture from that day. If you don’t see it under the options, click on media, then press encoder videos, and select the lecture from the section. If it still says live, click “Stop Broadcast”
# Under the video preview, use the cues tab to add a cue at the time marker for the beginning and the end of the lecture. Move the playhead to the desired place in the video where you want to add the cue, and then press add cue to auto choose that time stamp.
# Click download, under the three dots next to the video title. Choose the cues you set as the start and end points
# Once the file downloads, upload it to myBSF from the downloads folder.
# Press the red “OFF” button on the wall to the right of the sound board.
# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.
# Everything should be shut off now except the computer =)
# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.
# Use the Orange taped remote to retract the TV within the stage.
# Replace the lens cap on the camera (It should already be powered off)
# Turn off the Video and Presentation computers

← Older revision		Revision as of 19:54, 8 September 2025
Line 5:		Line 5:
	== Audio: ==		== Audio: ==

	# Turn on soundboard (Press the power button on the pad above the soundboard and then press “System On”)		# Turn on soundboard (Press the yellow power button on the pad above the soundboard and then press “System On”)
	# When asked to login, select BSF, then login, the password is “BSF” - all caps		# When asked to login, select BSF, then login, the password is “BSF” - all caps
	# Select yes to load User scene		# Select yes to load User scene
	# Turn on green “ON” button to the right of the board on the booth wall		# Turn on green “ON” button to the right of the board on the booth wall
	# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the ~~storage room~~ behind the stage		# Grab Microphone 3, Lav 1, and Acoustic 1 (Microphone 1 if you need the extra HH channel) from the desk behind the stage
			#* Mic 1 needed first meeting of the month for treasurer's report.
	# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 2”		# Grab the microphone from the right door in the middle of the booth. It will be labeled “Lav 2”

	== Lighting: ==		== Lighting: ==

	# Power the stage lights by pressing the power switch next to the blue lighting console once.		# Power the stage lights by pressing the rocking power switch next to the blue lighting console once.
	# Wake up the lighting computer by moving the mouse.		# Wake up the lighting computer by moving the mouse.
	# Log into user “lights” - the password is: Lights		# Log into user “lights” - the password is: Lights
Line 20:		Line 21:
	# Pull fader four all the way down, and the push it all the way up.		# Pull fader four all the way down, and the push it all the way up.
	# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”		# Press “PSET 1 1S” on the white box by the computer labeled “Unision Clamshell Controller”
	# If sections of the house lights above the seat are dark, turn off the switch on ~~“Panel~~ 3” in the back and turn back on.		# If sections of the house lights above the seat are dark, turn off the switch on “Rack 3” in the back and turn back on.

	== Video: ==		== Video: ==
Line 37:		Line 38:
	== Slides: ==		== Slides: ==

	# Restart the slides computer.		# Restart the slides computer by clicking the Apple icon in the top left corner of the screen and choosing "restart". You can press "yes" to any apps that request confirmation to quit.

	# Log into the BSF user using password “Frontline” - Case sensitive		# Log into the BSF user using password “Frontline” - Case sensitive
	# Turn on TV in front of the camera position.		# Turn on TV in front of the camera position.
Line 62:		Line 64:

	# Before the music starts, make sure the “FTB” button on the video switcher is flashing red.		# Before the music starts, make sure the “FTB” button on the video switcher is flashing red.
	# Press the ~~green start~~ button on the button pad to start the recording		# Press the "go rec" button on the button pad to start the recording
	# As the music starts, press “FTB” button.		# As the music starts, press “FTB” button.
	# You should now see the image on the screen		# You should now see the image on the screen
Line 82:		Line 84:
	# Click on the group bookmark in the bookmark bar.		# Click on the group bookmark in the bookmark bar.
	# Post that link to the BSFGRNEW - Lecture only group.		# Post that link to the BSFGRNEW - Lecture only group.
	# Send that same link via gmail.com to ~~EWLansingBSF~~@gmail.com , ~~giertie~~@~~yahoo~~.com , ~~Nikihaynes22@aol~~.~~com , knjroot~~@~~yahoo~~.com , ~~akingsworthy~~@~~hotmail~~.com , ~~Margaret.sharp73~~@gmail.com		# Send that same link via gmail.com to nhossink@gmail.com, connie.b.berg@gmail.com, bethany.arnold78@gmail.com, bsfkristal@gmail.com, aussiekasper@gmail.com.

	''NOTE: use CMD (next to the space bar) + C or V to copy and paste. =)''		''NOTE: use CMD (next to the space bar) + C or V to copy and paste. =)''
Line 102:		Line 104:
	== Shutdown ==		== Shutdown ==
	# Hold down the "shift" button on the blue lighting console and press release.		# Hold down the "shift" button on the blue lighting console and press release.
	# Power off the stage lights by pressing the power switch next to the light console once.		# Power off the stage lights by pressing the rocking power switch next to the light console once.
			#* This will only turn off the stage lights; house lights will remain on for groups.
	# Press the red “OFF” button on the wall to the right of the sound board.		# Press the red “OFF” button on the wall to the right of the sound board.
	# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.		# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.
			# Replace the dust cover on the sound board.
	# Everything should be shut off now except the computers =)		# Everything should be shut off now except the computers =)
	# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.		# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.
	# Press the "TV Down" button to lower the teaching TV.		# Press the "TV Down" button to lower the teaching TV.
	# Replace the lens cap on the camera.		# Replace the lens cap on the camera.
	# Restart the slides computer.		# Restart the slides computer if the video has finished uploading.

← Older revision		Revision as of 20:20, 25 August 2025
Line 86:		Line 86:
	''NOTE: use CMD (next to the space bar) + C or V to copy and paste. =)''		''NOTE: use CMD (next to the space bar) + C or V to copy and paste. =)''

	= ~~Shutdown &~~ Posting to MyBSF =		= Posting to MyBSF =

	# Once the lecture is done, go to studio.resi.io		# Once the lecture is done, go to studio.resi.io
Line 94:		Line 94:
	# Click download, under the three dots next to the video title. Choose the cues you set as the start and end points		# Click download, under the three dots next to the video title. Choose the cues you set as the start and end points
	# Once the file downloads, upload it to myBSF from the downloads folder.		# Once the file downloads, upload it to myBSF from the downloads folder.
	# * If the ~~livestream~~ video is unavailable or unusable *		# * If the Resi video is unavailable or unusable *
	## Remove the SD card from one of the video recorders next to the video switcher.		## Remove the SD card from one of the video recorders next to the video switcher.
	## Plug it into the back of the lighting computer.		## Plug it into the back of the lighting computer.
	## Open Finder and find the SD Card under locations.		## Open Finder and find the SD Card under locations.
	## Move the relevant file to the downloads folder and upload to myBSF as usual.		## Move the relevant file to the downloads folder and upload to myBSF as usual.

			== Shutdown ==
			# Hold down the "shift" button on the blue lighting console and press release.
			# Power off the stage lights by pressing the power switch next to the light console once.
	# Press the red “OFF” button on the wall to the right of the sound board.		# Press the red “OFF” button on the wall to the right of the sound board.
	# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.		# Press the “System Off” button on the button pad above the sound board, then press “Yes” to confirm.
	# Everything should be shut off now except the ~~computer~~ =)		# Everything should be shut off now except the computers =)
	# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.		# Return the Mic to the drawer in the tech booth, and the wireless guitar and mic packs, as well as mic 3 to their charging dock behind the stage.
	# Press the "TV Down" button to lower the teaching TV.		# Press the "TV Down" button to lower the teaching TV.
	# Replace the lens cap on the camera.		# Replace the lens cap on the camera.
	# Restart the slides computer.		# Restart the slides computer.